Hydro Drive, Simplified: Our hydro drive system has no hoses to leak and just one easy-to-change belt. Only simple, annual maintenance is required. It also lowers the center of gravity for improved handling.
Unibody Frame: Our one-piece body frame is a classic case of “less is more.” Because, fewer parts equal more strength. And, more durability. So, in the interest of accuracy, the Lazer Z’s unibody frame is actually a case of “less is way more.”
Less Time At The Pump: Gas-powered E-Series models have a single 8-gallon tank with one fill location.
On-Board Diagnostics: Check vital functions at a glance on the digital screen. An electronic fuel gauge with low fuel warning on all Lazer Z units, battery voltage warning, hour meter and OPC safety switch monitoring make troubleshooting easy.
Fewer Grease Points: With just four grease points that only need annual greasing, the Lazer Z delivers maximum performance with minimum maintenance. Greaseless spindles and only four grease points on the entire machine.
Ultracut Series 4 Deck: This full-floating deck uses maintenance free spindle with a splined blade driver to stop bolt tightening on impacts. And, our patented bearing design on idler arm pivots only needs annual service.
Rear Discharge Deck: Available in 60 and 72 inch cutting widths, the rear discharge deck offers increased clipping discharge control, reduced noise, and the ability to trim on both sides of the cutting deck while keeping the operator clean.
Tool-less Belt Removal: Deck and hydro belt can be installed without using any tools.
Blade Tip Speed: Approximately 18,500 fpm.
Blades: 3 Blades at 20.50" Length
Cutting Heights: 1.0" (2.5 cm) to 5.5" (11.8 cm) in 0.25" (0.64 cm) increments adjustable from operator’s seat.
Deck Construction: 7-gauge high strength alloy top that is formed and continuously seam welded, with 7-gauge high strength alloy side skirt.
Deck Style: Floating Deck
Deck Style Description: Full-floating UltraCut Rear Discharge Deck. Rear-discharge standard with option to mulch.
Width / Cutting Deck: 60"
Height: 70 in. (177.8 cm)
Length: 87.2 in. (221.5cm)
Width: 66.2 in. (168.1 cm)
Curb Weight: 1240
Blade Spindles: No maintenance, sealed and non-greasable spindles; 7.75"-diameter cutter housing with 25mm (.98") diameter spindle shaft and splined blade driver.
Cup Holder: Standard
Drive Tires: 24 x 12-12, 4 ply Super Turf®
Electrical: 12-volt battery with 15-amp alternator.
Front Caster Tires: 13 x 6.5-6, smooth-tread, semi-pneumatic.
Parking Brake: Lever-actuated disc brake.
Seat: Deluxe, bolstered suspension seat with Elastomeric Vibration Control material. Adjustment: Fore and aft from Operators’ Position.
Steering Control: Hydraulically dampened twin levers, adjust fore and aft. Adjustable dampeners (3 positions) to customize drive responsiveness. Also adjustable to 2 height positions.
Tractor Frame: Unibody, welded, heavy-duty 1.5" x 3" tubular steel.
Air Filter: Heavy-duty canister air filtration system
Carb Compliant: No
Casters: .50" thick caster yoke arms.
Deck Lift: Standard; foot-controlled deck lift changes cutting height and lifts the deck to maneuver around obstacles, or place in transport position.
Drive Description: Two Exmark exclusive Parker unitized pump and wheel motor systems with no hoses, integrated cooling fans, shock valve, 1.7-quart integrated reservoir, spin-on filter and heavy-duty components. 12 cc pumps and 14. 5 cubic inch motors.
Drive Wheel Release: Allows unit movement without engine running.
Engine Brand: Kawasaki®
Engine Displacement: 726
Engine Model: FX730V
Engine Series: V-Twin
Engine Speed: 3,750 rpm
Engine Type: Carbureted
Fuel Capacity: 8-gallon (30.3-L) single fuel tank with single fill location.
Fuel Indicator: Yes - electronic Sender
PTO Engagement: MagStop electromagnetic 200-ft-lb clutch with spot brake
ROPS: 2-post foldable ROPS standard with seat belt and latch.
Safety Package: Operator Presence Controls (OPC) and drive system interlock, with safety interlock system indicators.